The TempTAB Trakker software contains sample data. Once you download the Excel Workbook, you can write over the sample data on the "Input Tab. The workbook requires at least two runs before it will start graphing. Help is available at 614-818-1343/1338.
Using the TempTAB Trakker Software “ General Instructions
The TempTAB Trakker Software is an Excel Workbook.
There are three tabs on the bottom left hand corner of the screen. "Instructions, "Input and "Furnace.
Start by clicking on the "Instructions Tab then scroll down to the "Quickstart Instructions.
1) From the pull down Menu select "Centigrade or "Fahrenheit.
2) Initially the offset should be set to "0. This field can be used later to calibrate the TempTABs to your process.
3) Enter the name of your Furnace.
4) Determine the locations inside your furnace that you want to monitor and enter the locations in the cells. The software allows you to enter between 1 and 9 locations.
To erase data, highlight the cell(s) to be erased, then Edit, Clear Contents
Go to the "Input tab
Click on the cell below the heading "Product and Batch. A drop down menu should appear. Select the TempTab Product and batch number for the TempTAB you are using.
Click on the cell, below the heading "Time. A drop down menu should appear. Depending on the product you are using there are usually several different schedules available. (10, 30, 60, 120, 240+ minutes and S10, S30, S60, S120, S240) Select the schedule that is closest to your process. The single numbers represents TempTAB results based on inserting the TempTABs into a hot furnace for the specified number of minutes then cooled in air. The "S in the second group represents a "Sintering Profile that has a ramp rate up to the set point then a hold time equal to the number of minutes. Ie: A "30 " profile represents placing a TempTAB into a hot furnace for 30 minutes then removing it and cooling in air. An "S30 profile represents placing the TempTAB into a furnace, ramping up to the setpoint as in a sintering process, then once at the setpoint temperature, the process is held for 30 minutes.
Once you have the selected the correct "Product and Batch and the correct "Time, you can highlight the two fields and the cells below you want to populate and then Edit, Fill Down. Theses can be used for future runs.
Date and Run# are optional but the date does appear as a label on the output graph.
The TempTAB dimensions are entered to the right of the run # on this page once the TempTABs have gone through the furnace and have been measured.
Go to the "Furnace tab.
The furnace Tab contains the results. There will be a graph at the top of the page and a temperature table at the bottom of the page. The scale on the graph can be easily changed by "right-clicking on the top number in the scale then hitting "Format Axis, then go to "Scale. Enter the maximum and minimum temperatures you want to graph, then hit "OK.
The data in the bottom table can be highlighted and copied to another spreadsheet or workbook.
To clear data out of the workbook it is always best to highlight the data, then edit, clear, contents.
TempTAB 300 can be used in the temperature range of 850-1,100°C (1562-2012°F).
TempTAB 400 can be used in the temperature range of 1,000-1,200°C (1,832-2,192°F).
TempTAB 600 can be used in the temperature range of 1,100-1,300°C (2012-2372°F).
TempTAB 650 can be used in the temperature range of 1,200-1,500°C (2192-2732°F).
TempTAB 700 can be used in the temperature range of 1,450-1,750°C (2,642-3,182°F).
[PDF] View Batch #200DIF (°F) »
[PDF] View Batch #200DIF (°C) »
[PDF] View Batch #300 DGF (°C) »
[PDF] View Batch #300 DGF (°F) »
[PDF] View Batch #300 MYI (°C)»
[PDF] View Batch #300 MYI (°F)
[PDF] View Batch #300 SMK (°C)»
[PDF] View Batch #300 SMK (°F)»
[PDF] View Batch #300 LCI (°C) »
[PDF] View Batch #300 LCI (°F) »
[PDF] View Batch #400 BPD (°C) »
[PDF] View Batch #400 BPD (°F) »
[PDF] View Batch #400 JNI (°C) »
[PDF] View Batch #400 JNI (°F) »
[PDF] View Batch #600 JSI (°C) »
[PDF] View Batch #600 JSI (°F) »
[PDF] View Batch #600 ZGD (°C) »
[PDF] View Batch #600 ZGD (°F) »
[PDF] View Batch #650 MFI (°F) »
[PDF] View Batch #650 MFI (°C) »
[PDF] View Batch #650 6TI (°C) »
[PDF] View Batch #650 6TI (°F) »
[PDF] View Batch #700 WLL (°C) »
[PDF] View Batch #700 WLL (°F) »
[PDF] View Batch #700 KSI (°C) »
[PDF] View Batch #700 KSI (°F) »
[PDF] View Batch #700 SSK (°C) »
[PDF] View Batch #700 SSK (°F) »
FROM THE BLOG...
06/23/2020Shelf Life of Cones
Do cones have a shelf life? At the Edward Orton Jr. Ceramic Foundation, a common question asked to...
06/04/2020Orton partners with United Parcel Service for small package shipments outside the United States
The cost to obtain a small quantity of Orton cones or products is sometimes prohibitive if they...
05/12/2020New Test Equipment Installed
Orton's Materials Testing Service Department recently added a new laser flash machine to measure thermal...